Eshop roka 2025 s vykurovacou technikou

Press-GAS - ulkoinen kierteitys - 3/4"Mx26 IVAR.PT 5608-GAS

Mã số: 510004GAS
Chưa được đánh giá Chi tiết đánh giá
11,53 € –20 %
Vykurovacia technika Prechodka PRESS-GAS  - závit vonkajší - 3/4"Mx26
11,53 € –20 % 9,22 € / Cái 7,50 € Ngoại trừ thuế VAT Giá đo lường:
Giao hàng quốc tế
Varastossa (12 Cái)

Thông tin chi tiết

Mô tả chi tiết sản phẩm

Press-GAS Pressfitting, IVAR.PT 5608-GAS, koko: 3/4" M x 26, pakkaus: 5 pussia / 130 koko laatikko
- ulkoinen kierre
 
  • maksimipaine PN 10, T = -20 °C - +60 °C
  • maksimikäyttöpaine PN 5
  • ALPEX-GAS -putken liittämiseen sisäiseen kierre
  • materiaali messinki CW617N, tiiviste HNBR
  • yhteensopiva B-tyypin puristimien kanssa

 

Suositeltu käyttö PTN 704 05 mukaan

Usein kysytyt kysymykset

  • Mitä työkaluja tarvitsen liitososan asentamiseen? Puristusliitokset vaativat erikoistyökaluja, joissa on oikean tyyppinen leuka (yleensä merkitty B, F tai TH järjestelmän mukaisesti) sopivan koon ja tyypin mukaisia - ilman oikeaa työkalua liitosta ei voi muodostaa eikä tarkistaa.
  • Kuinka tiedän, että liitos on oikein puristettu? Laadukkaat puristusliitokset sisältävät puristusindikaattorin (esim. tiivisteellinen O-rengas, joka vuotaa epäjatkuvan puristuksen yhteydessä) - ennen upotusta seinään tai tasoitukseen on aina tehtävä järjestelmän paineentarkistus.
  • Voiko liitoksen purkaa sen jälkeen, kun se on puristettu? Ei, toisin kuin ruuviliitoksessa, puristusliitos on pysyvä ja sen purkaminen edellyttää liittimen leikkaamista ja korvaamista uudella.
  • Onko asennuksen suoritettava ammattilainen? Kyllä, puristusliitosten asentaminen vaatii ammattitaitoa ja oikein kalibroituja työkaluja - suosittelemme jättämään lämmityskoneen asentajalle, varsinkin jos liitokset upotetaan seinään tai tasoitukseen ilman myöhempää mahdollisuutta tarkastukseen.

Các thông số bổ sung

Danh mục hàng: IVAR.PT 5608-GAS - siirtoliittimet - ulkokierre
Bảo hành: 2 năm
Trọng lượng: 0.087 kg
Kierteen koko: 3/4"
Tuotteen tyyppi: PRESS-liitin
Saatavuus: Varastossa tai toimittajalla
Posledná aktuálizacia ceny: 13.04.2026 1:10:43

Đánh giá sản phẩm

Hãy là người đầu tiên đăng bài báo về mặt hàng này!

Đừng điền vào ô này

Bạn đánh giá sản phẩm này như thế nào? Chọn từ 1 đến 5 sao, trong đó 1 là tệ nhất và 5 là tốt nhất.

Thảo luận

Đừng điền vào ô này

Danh sách các thảo luận

A avatar của tác giả 15.11.2026 20:47
Živjo, oče ima doma plinovod in rabimo to spojko za priklop na plin, zanima me če je to varno za plin ali je to sam za vodo in ogrevanje? Pa a rabmo res nekoga poklicat da to zmontira, al lahko sam poskusimo?
A avatar của tác giả 15.11.2026 20:47
Ta spojka je narejena točno za plin - gre za PRESS-GAS izvedbo s HNBR tesnilom, ki je kompatibilno s čeljustmi tipa B, in je namenjena za uporabo po PTN 704 05. Glede montaže pa - ne, tega raje ne poskušajte sama, ker rabiš pravo stiskalnico s pravilnimi čeljustmi, poleg tega je spoj po stiskanju trajen (ne da se ga razstaviti). Pri plinskih inštalacijah je montaža s strani inštalaterja obvezna tudi zaradi varnosti, zato priporočamo, da to prepustite strokovnjaku.

IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.

 

Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.

 

Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.

 

“Made in Italy” adds value

IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.

The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.

 

Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.

The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.


As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.

Vytvořil Shoptet | Design Shoptak.cz.