Eshop roka 2025 s vykurovacou technikou

Kulmaliitin 3/4" FF

Mã số: 2520002
Chưa được đánh giá Chi tiết đánh giá
4,54 € –18 %
Fiting Koleno 3/4" FF
4,54 € –18 % 3,69 € / Cái 3 € Ngoại trừ thuế VAT Giá đo lường:
Giao hàng quốc tế
4–7 päivää

Thông tin chi tiết

Mô tả chi tiết sản phẩm

Messinkinen kierteinen mutka 3/4" FF on yleisin liitos teräsputkistoon, esimerkiksi kattilan ja muiden lämmitysratkaisujen alle.

Messinkinen kierteinen mutka – muuttaa putkireitin suuntaa 90° (tai muun kulman tietyn tyypin mukaan). Messinki on pitkäaikaisesti testattu, standardi materiaali kierteisille vesijohto- ja lämmitysputkistoille sen korroosionkestävyyden ja luotettavan tiiviyden ansiosta, kun liitos on oikein kiristetty.

Usein kysytyt kysymykset

  • Miten valita oikea koko liittimelle? Kierrerakenteen mitta (esim. 1/2", 3/4", 1") on oltava tarkalleen sama kuin putkistossa tai liittimessä, johon liitin liitetään - FF (sisäinen-sisäinen), MF (ulkoinen-sisäinen) ja vastaavat lyhenteet nimessä osoittavat kierrerakenteen tyypin eri puolilla liittimen.
  • Mitä FF ja MF lyhenteet tarkoittavat nimessä? F (female, sisäinen kierre) ja M (male, ulkoinen kierre) osoittavat kierrerakenteen tyypin kyseisellä puolella liittimen - esimerkiksi "FF" tarkoittaa sisäistä kierre molemmilla puolilla, "MF" ulkoinen toisella ja sisäinen toisella puolella.
  • Onko tiivistysmateriaalin käyttö asennuksessa tarpeen? Kyllä, kierteisiin liitoksiin käytetään standardisti tiivistysmateriaalia (esim. teflonnauha tai hamppu lanka tiivistyspastaa), jotta varmistetaan liitoksen täydellinen tiiviys - pelkkä kierre ilman tiivistettä ei luotettavasti tiivistä.
  • Onko asennuksen suoritettava ammattilainen? Yksinkertaisen kierteisen liitoksen voi tehdä myös kotitalouden mestari perustaidoilla, mutta jos tehdään toimivaan putkistoon (erityisesti kaasu- tai painevesi-/lämmitysjärjestelmä) suosittelemme ottamaan yhteyttä asentajiin, jotka myös tarkistavat liitoksen tiiviyden asennuksen jälkeen.
  • Mikä materiaali ja mikä paineasteikko tällä liittimellä on? Suorituskyky on messinkiä, sopii tavallisiin vesijohto- ja lämmitysputkistoihin - tarkat nimelliset paine- ja lämpötilaluvut (jos ne on mainittu tietyssä tuotteessa) löytyvät teknisistä tiedoista yllä.

Các thông số bổ sung

Danh mục hàng: Kulmat
Bảo hành: 2 năm
Trọng lượng: 0.1 kg
Liittimen tyyppi: kaari / mutka
Kierteen koko: 3/4"
Materiaali: messinki
Liitäntätyyppi: sisäkierre
Saatavuus: Varastossa tai toimittajalla

Đánh giá sản phẩm

Hãy là người đầu tiên đăng bài báo về mặt hàng này!

Đừng điền vào ô này

Bạn đánh giá sản phẩm này như thế nào? Chọn từ 1 đến 5 sao, trong đó 1 là tệ nhất và 5 là tốt nhất.

Thảo luận

Đừng điền vào ô này

Danh sách các thảo luận

J avatar của tác giả 25.10.2026 12:46
I am trying to put this on my steel heating pipes but I am not sure if the size is right and do I need some special tape to stop it from leaking?
A avatar của tác giả 25.10.2026 12:46
This brass elbow is designed specifically for 3/4" steel pipes, so just make sure your pipe has the same thread size. You should definitely use sealing tape or hemp paste on the threads, because the metal alone won't seal properly. It is a standard part often used under boilers to change the pipe direction by 90 degrees.

IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.

 

Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.

 

Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.

 

“Made in Italy” adds value

IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.

The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.

 

Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.

The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.


As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.

Vytvořil Shoptet | Design Shoptak.cz.