Eshop roka 2025 s vykurovacou technikou

Adapter - sisäkkäinen kierre ja yksi liitospää - ruostumaton AISI 316 - 18mm-Rp3/4" IVAR.IVN86

Mã số: IVN86.1834
Chưa được đánh giá Chi tiết đánh giá
16,85 € –20 %
Vykurovacia technika Prechodka - s vnútorným závitom a jedným zásuvným koncom - nerez AISI 316 - 18mm-Rp3/4"
16,85 € –20 % 13,48 € / Cái 10,96 € Ngoại trừ thuế VAT Giá đo lường:
Giao hàng quốc tế
Varastossa toimittajalla

Thông tin chi tiết

Mô tả chi tiết sản phẩm

Liitos - sisäpultilla ja yhdellä liitospäällä - N - 18mm-Rp3/4"

  • PN 16, T = -20 °C - +85 °C - max. +120 °C
  • liitos sisäpultilla ja yhdellä liitospäällä d x Pultti
  • käyttötarkoitus: terveystekniset asennukset, sprinklerijärjestelmät,
    lämmitysjärjestelmät, paineilma, aurinkolämpöjärjestelmät, inertit kaasut ja teollisuus
  • materiaali: ruostumaton teräs luokka Wst. Nr. 1.4404 (AISI 316L)

Huomio: Tiivistämätön jos ei ole puristettu ja puristusindikaattorilla halkaisijaan 54 mm.

Usein kysyttyä

  • Mihin tarkoitukseen tämä putki on tarkoitettu? Tarkka määrittely (veden, lämmityksen, kaasun, aurinkolämpöjärjestelmien, paineilman jne. jakelujärjestelmät) löytyy tuotteen kuvauksesta ja teknisistä tiedoista - eri materiaalit (ruostumaton teräs, hiiliteräs) kestävät korroosiota eri tavalla ja niillä on eri sertifioidut väliaineet.
  • Miten tämä putki liitetään? Yleensä puristusliittimillä (press) tai hitsatuilla liitoksilla, järjestelmästä ja halkaisijasta riippuen - käytä yhteensopivia liitososia saman järjestelmän kanssa.
  • Onko asennuksen suoritettava ammattilainen? Kyllä, erityisesti kaasu-, paineilma- tai hitsattujen liitosten jakelujärjestelmissä asennus on varattu henkilölle, jolla on asianmukainen ammattipätevyys.

Các thông số bổ sung

Danh mục hàng: IVAR.IVN86 - siirtoliittimet - sisäkierteellä ja pistokepäällä
Bảo hành: 2 năm
Saatavuus: Varastossa tai toimittajalla
Hinnan viimeisin päivitys: 26.05.2026 8:49:59

Đánh giá sản phẩm

Hãy là người đầu tiên đăng bài báo về mặt hàng này!

Đừng điền vào ô này

Bạn đánh giá sản phẩm này như thế nào? Chọn từ 1 đến 5 sao, trong đó 1 là tệ nhất và 5 là tốt nhất.

Thảo luận

Đừng điền vào ô này

Danh sách các thảo luận

J avatar của tác giả 19.11.2026 10:16
Good morning, my dad wants to use this to connect our new heating pipe to a 3/4" valve, is this adapter actually okay for heating systems or just water stuff? Also does it need special tools or can we just push it on?
A avatar của tác giả 19.11.2026 10:16
Yes, heating systems are listed as one of the intended uses, along with sanitary installations, solar systems and a few others. It's rated PN16 and works up to 85°C normally (max 120°C short term), so a standard heating setup is fine. Just keep in mind the push-fit end needs an actual press-fitting tool to seal properly - it will leak if it's only pushed on by hand, so this part of the job should really be done by someone experienced with press systems.

IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.

 

Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.

 

Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.

 

“Made in Italy” adds value

IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.

The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.

 

Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.

The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.


As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.

Vytvořil Shoptet | Design Shoptak.cz.