Eshop roka 2025 s vykurovacou technikou

90° Press Knee - External Thread - 5/4"M x 40 IVAR.PT 5711

Mã số: 510033
Chưa được đánh giá Chi tiết đánh giá
34,44 € –20 %
Vykurovacia technika Koleno PRESS 90°  - závit vonkajší - 5/4"Mx40
34,44 € –20 % 27,55 € / Cái 22,40 € Ngoại trừ thuế VAT Giá đo lường:
Giao hàng quốc tế
Varastossa toimittajalla

Thông tin chi tiết

Mô tả chi tiết sản phẩm

90° press-kyynärpää - ulkoinen kierre, IVAR.PT 5711, koko: 5/4" M x 40, pakkaus: 1 pussia / 30 koko laatikko 

 

Usein kysyttyä

  • Mitä työkaluja tarvitsen tämän liittimen asennukseen? Press-liittimet vaativat erikoistuneet puristuspihdit oikean tyyppisellä leualla (yleensä merkitty B, F tai TH järjestelmän mukaan) vastaamaan liittimen kokoa ja tyyppiä - ilman oikeaa työkalua liitosta ei voida muodostaa tai tarkistaa.
  • Kuinka tiedän, että liitos on oikein puristettu? Laadukkaat press-liittimet sisältävät puristusindikaattorin (esim. tiiviste O-rengas, joka vuotaa, jos puristus ei ole valmis) - ennen kuin liitos upotetaan seinään tai laastiin, on aina tehtävä järjestelmän paineentarkistus.
  • Voidaanko liitos purkaa sen jälkeen, kun se on puristettu? Ei, toisin kuin ruuviliitoksessa, puristusliitos on pysyvä ja sen purkaminen vaatii liittimen leikkaamisen ja korvaamisen uudella.
  • Pitäisikö asennuksen suorittaa ammattilainen? Kyllä, liittimien puristus vaatii ammattitaitoa ja oikein kalibroituja työkaluja - suosittelemme antamaan lämmitysasentajalle, varsinkin liitoksille, jotka upotetaan seinään tai laastiin ilman mahdollisuutta myöhempää tarkastusta.

Các thông số bổ sung

Danh mục hàng: 90° press-kulma - ulkokierre
Bảo hành: 2 năm
Trọng lượng: 0.391 kg
Liittimen tyyppi: kaari / mutka
Putken halkaisija: 40 mm
Liitäntätyyppi: puristusliitos
Saatavuus: Varastossa tai toimittajalla
Hinnan viimeisin päivitys: 26.05.2026 13:54:26

Đánh giá sản phẩm

Hãy là người đầu tiên đăng bài báo về mặt hàng này!

Đừng điền vào ô này

Bạn đánh giá sản phẩm này như thế nào? Chọn từ 1 đến 5 sao, trong đó 1 là tệ nhất và 5 là tốt nhất.

Thảo luận

Đừng điền vào ô này

Danh sách các thảo luận

J avatar của tác giả 13.11.2026 09:39
Dober dan, zanima me, ali je za montažo tega kolena na cev ALPEX potrebna enaka čeljust kot za ravne press fitinge iste dimenzije, ali gre za posebno izvedbo čeljusti zaradi kotne oblike fitinga?
A avatar của tác giả 13.11.2026 09:39
Dober dan, čeljust je ista, pomembna je samo velikost in tip (B, F ali TH), ne oblika fitinga. Ker gre za velikost 5/4" M x 40, potrebujete čeljust, ki ustreza tej dimenziji in je kompatibilna z enim od teh treh tipov - oblika kolena na to nima vpliva. Če niste prepričani, kateri tip čeljusti ima vaš inštalater, preverite pri njem oziroma pri dobavitelju orodja.
R avatar của tác giả 27.09.2026 20:07
Zdravím, chcem sa opýtať, či toto koleno 5/4"Mx40 PRESS je vhodné na pripojenie čerpadla k rozdeľovaču pri podlahovom kúrení, alebo by som mal radšej siahnuť po inom type spojky?
A avatar của tác giả 27.09.2026 20:07
Toto koleno je určené na lisované spoje (PRESS systém) s vonkajším závitom 5/4", takže na priame závitové pripojenie čerpadla by malo byť v poriadku, pokiaľ sa závit zhoduje. Dôležité je overiť, či máte na protiľahlej časti vnútorný závit 5/4". Ak si nie ste istý kombináciou dielov, radi vám poradíme pred objednávkou.

IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.

 

Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.

 

Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.

 

“Made in Italy” adds value

IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.

The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.

 

Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.

The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.


As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.

Vytvořil Shoptet | Design Shoptak.cz.