Eshop roka 2025 s vykurovacou technikou

90° Press Gas Bend - 42mm IVAR.IVN20 GAS

Mã số: IVNGAS20.42
Chưa được đánh giá Chi tiết đánh giá
50,55 € –20 %
Vykurovacia technika Oblúk 90° PRESS GAS - 42mm
50,55 € –20 % 40,44 € / Cái 32,88 € Ngoại trừ thuế VAT Giá đo lường:
Giao hàng quốc tế
Varastossa toimittajalla

Thông tin chi tiết

Mô tả chi tiết sản phẩm

90° PRESS GAS - 42 mm kaari

Huomautus: Press GAS 76,1, 88,9 ja 108 mm -liittimien mitat tilaustuotteena.

Usein kysyttyä

  • Mitä työkaluja tarvitsen tämän liittimen asennukseen? Press-liittimet vaativat erikoistuneet puristuspihdit, joissa on oikean tyyppinen leuka (yleensä merkitty B, F tai TH järjestelmän mukaan) vastaamaan liittimen kokoa ja tyyppiä - ilman oikeaa työkalua liitosta ei voi muodostaa eikä tarkistaa.
  • Kuinka tiedän, että liitos on oikein puristettu? Laadukkailla press-liittimillä on puristusindikaattori (esim. tiiviste O-rengas, joka vuotaa, jos puristus ei ole valmis) - ennen kuin liitos upotetaan seinään tai laastiin, on aina tehtävä järjestelmän paineenkestävyystesti.
  • Voiko liitos avata sen jälkeen, kun se on puristettu? Ei, toisin kuin puristusliitoksessa, puristusliitos on pysyvä ja sen purkaminen vaatii liittimen leikkaamisen ja korvaamisen uudella.
  • Pitäisikö asennuksen suorittaa ammattilainen? Kyllä, liittimien puristus vaatii ammattitaitoa ja oikein kalibroituja työkaluja - suosittelemme antamaan lämmitysteknikolle/asentajalle, varsinkin liitoksille, jotka upotetaan seinään tai laastiin ilman mahdollisuutta myöhempään tarkastukseen.

Các thông số bổ sung

Danh mục hàng: IVAR.IVN20 GAS - 90° kulmat FF PRESS GAS
Saatavuus: Varastossa tai toimittajalla
Posledná aktuálizacia ceny: 13.04.2026 1:10:37

Đánh giá sản phẩm

Hãy là người đầu tiên đăng bài báo về mặt hàng này!

Đừng điền vào ô này

Bạn đánh giá sản phẩm này như thế nào? Chọn từ 1 đến 5 sao, trong đó 1 là tệ nhất và 5 là tốt nhất.

Thảo luận

Đừng điền vào ô này

Danh sách các thảo luận

R avatar của tác giả 15.11.2026 15:43
Czy w przypadku kształtki PRESS GAS o średnicy 42 mm zalecane jest zastosowanie uszczelki O-ring typu HNBR, a czy połączenie to pozwala na ewentualne rozmontowanie i ponowne użycie po wykonaniu presowania?
A avatar của tác giả 15.11.2026 15:43
Tak, produkt ten wyposażony jest w żółtą uszczelkę O-ring wykonaną z materiału HNBR. Należy jednak pamiętać, że połączenie presowe jest trwałe i po jego zapięciu nie można go rozmontować – w razie potrzeby demontażu konieczne będzie przecięcie kształtki i wymiana jej na nową.
B avatar của tác giả 26.10.2026 12:57
Bună, am auzit că acest colier e pentru gaz. Pot să-l folosesc și pentru instalația de apă caldă din casă sau e doar pentru metan?
A avatar của tác giả 26.10.2026 12:57
Salut! Acest model este special conceput doar pentru rețelele de gaz (metan, biogaz, propan) și nu este recomandat pentru apă. Este fabricat din oțel inoxidabil rezistent la temperaturi între -20°C și +70°C, dar materialul garniturii este optimizat pentru gaze. Pentru apă îți recomandăm să cauți alte fitinguri din categoria noastră dedicate instalatiilor sanitare.

IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.

 

Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.

 

Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.

 

“Made in Italy” adds value

IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.

The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.

 

Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.

The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.


As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.

Vytvořil Shoptet | Design Shoptak.cz.